Showing results: 361 - 375 of 384 items found.
-
COMe Type 7 Ice Lake-D STKit -
ADLINK Technology Inc.
The Type 7 Starter Kit Plus consists of a COM Express Type 7 module with ATX size Type 7 reference carrier board that offers one PCI Express x16 slot with proprietary pinout for 10GbE adapter card that convert 10GBase-KR to 10GbE Optical Fiber or 10GbE Copper signal, one PCI Express x16 slot, two PCI Express x8 slots, Serial ATA, USB3.0/2.0, Gigabit LAN and Super I/O. in addition, a IPMI BMC (miniBMC) located on carrier board connect to COM Express Type7 module by NC-SI interface to support some of out-of-band management features. All necessary cables are included.
-
409B -
Novatech Instruments , Inc.
The 409B generates four independent, phase synchronous sine wave output signals and is programmable in 0.1 Hz steps from 0.1 Hz to 171 MHz. Programming is via an RS232 serial interface. Phase is 14-bit programmable and amplitude is 10-bit programmable. Internal memory can store a sequence of settings. The -AC option is available to enable users to step through settings using an external trigger. It is accurate to 1.5 ppm using the on board TCXO timebase or you can use an external timebase, There is also a /R option that provides a way to lock to and track an external 10MHz frequency input. A line powered AC adapter and SOF8_409 windows software on a CD are included.
-
Copernicus Technology Ltd
Copernicus Technology supply test hardware accessories to support Intermittent Fault Detection testing using VIFD™ and IFDIS™ test equipment, such as Interface Test Adapters (ITA). We also supply and repair general purpose and customer-spec test hardware accessories: ITAs, Break-Out Boxes (shown below) and Mobile Vibration Systems. The Mobile Vibration System can be quickly set up in repair bays for applying environmental stimulus to components and wiring harnesses during testing.
-
SKU-011-01 -
Amfeltec Corp.
The PCI to PCI Express Adapter simply turns your computer’s existing PCI slot into a PCI Express slot. This provides a seamless interface for older PCI systems to accept new PCI Express devices – making it possible to utilize old test equipment (computers, PCI extenders, PCI bus analyzers etc.) during migration from PCI to the PCI Express interface.There is no need to purchase additional software or to install new device drivers; simply plug & play!
-
PCI EmbeddedComputer Systems
The PCI-Adapter is a carrier board, allowing the operation of any standard (desktop) PCI card in a CompactPCI® system. The PCI-Adapter acts as a PCI bridge, providing an electrically and mechanically optimized interface between PCI and CompactPCI® system. Our adapters include a PCI Bridge. Some competitor products do not provide a PCI bridge, thus reducing adapter costs by tolerating a violation of the PCI specs. Overall PCI compatibility however is a must in order to achieve total system reliability. Please bear these facts in mind, when comparing prices of PCI-Adapters. All modern operating systems can treat a PCI bridge in a plug and play manner meaning that the bridge remains virtually transparent, as if the PCI component(s) behind the bridge on the secondary PCI bus were part of the primary PCI bus. Using the PCI-Adapter/bridge allows standard PCI boards to work in a CompactPCI® system is both a reliable technical solution, and a smart economical decision. The PCI-Adapter frees the system integrator from the need of a redesign of PCI cards already available to the CompactPCI® standard. This is a great advantage, especially when time to market is critical, or the number of systems to be built is limited, or the function to be implemented has fast innovation cycles.
-
xiX -
XIMEA GmbH
*Smallest camera featuring Sony Pregius™ - Compact with only 26.4 x 26.4 x 31 mm and 30 grams (1)*Fast CMOS - High speed, high frame rate: from 2.3 Mpix at 166 Fps to 50 Mpix at 33 Fps*Cool economy - Low power consumption with under 3 Watt and minimal heat dissipation*All-around support - support for Windows 7 and 10, macOS, Linux, ARM and embedded platforms*Industry standard - Data and control interface complies with PCI Express External Cabling Specifications*Adaptable potential - Available with two flat ribbon flex cable connectors: parallel and perpendicular *Software interfaces - GenICam / GenTL and highly optimized API / SDK for Image Processing*Connectivity and Synchronization - Programmable opto-isolated input and output, 4 status LEDs*Lens control - EF-mount Interface allows remote control of aperture, focus and image stabilization*Highly Customizable - Variety of sensor options including Sony IMX287, IMX273, IMX249, IMX265, IMX264, IMX267, IMX304 available in board level stack for OEM use and with switches and adapters*Interoperability increase - Continuous embrace of new software and hardware partners*Cost efficient - Excellent value through utilization of the newest technologies including Sony Pregius™
-
WST100 -
Eurostat Group
• Tester designed for checking the conformity of operators wrist strap and/or shoes to the ESD protection standard.• It is also designed to be permanent wall mounted in a production facility for daily testing of employee’s wrist straps and footwear.• Easy to operate, red and green LEDs give clear “pass” or “fail” indication• Individual tests for the wrist strap, the right and left shoe• Can register up to 60 000 different measurements• Output for interface with PC or automatic door opening system• Operates battery that can be supplemented with an AC net adaptor• Tester and calibration plug are delivered with a certificate ofcalibration
-
emPower -
SEGGER Microcontroller GmbH & Co. KG
The emPower eval board provides a comprehensive set of SEGGER's middleware products, accelerating the start of any embedded project. SEGGER's embOS real-time operating system is at the heart of the evaluation. Furthermore, evaluation versions of the file system emFile, graphics library emWin, emUSB Host & Device, and TCP/IP stack embOS/IP (including web server demo) enable full use of the available emPower peripherals. emPower also features a J-Link OB, an on-board version of SEGGER's market-leading debug probe J-Link, which includes drag & drop programming and COM-Port support. There are three expansion interfaces to easily connect additional modules. Each connector provides I2C, SPI, UART, GPIO/timer, analog input and power. A display adapter connector enables the connection of small TFT displays. The emPower board is powered by USB only. Current consumption drawn strongly depends on the application and connected peripherals. Idle consumption is approx. 85 mA.
-
LEON Bench -
Konrad Technologies GmbH
The LEONBench test system is a flexible and scalable test system that features an excellent signal integrity and a high-quality fixture interface. This is achieved by combining a cableless connection from ABex modules to Virginia panel interface connectors. The system is optimized for high pin count test applications. Furthermore, it can be equipped with vacuum and pneumatic. Support for multi-level contact fixtures enables separate contact levels for FCT and ICT. The Konrad ITA (Interchangeable Test Adapter) frame allows various fixture houses all over the world to build custom fixtures for the LEONBench. Up to 15U additional rack space allows adding a bunch of high-performance measurement devices from various manufactures. An integrated power distribution unit takes care about power on and off sequencing.As part of the LEON Family, LEONBench is based on the ABex platform which directly incorporates Konrad analog bus technology and PXI/PXIe in one chassis.
-
Extech DL150 -
Extech Instruments Corporation
The DL150 is a True RMS AC voltage and current data logger. Data log up to 100,000 readings of TRMS AC Voltage (600) or Current (200 Amp) with a user programmable sample rate from 1 second to 24 hours. LCD displays time/date, current reading, min/max, and if the user settable high/low alarms have been exceeded. Readings can be downloaded to your PC via the USB interface. Featuring Normal, Peak, and Capture (user specified trigger level) recording modes. Complete with current clamp, test leads, alligator clips, software, USB cable, 110-Volt AC Adapter, and four (4) AAA batteries.
-
Extech DL160 -
Extech Instruments Corporation
The DL160 is a Dual Input True RMS AC Voltage/Current Data logger. Simultaneously data log 2 channels of up to 256,000 readings of TRMS AC Voltage (600V) or Current (200A) or one AC Voltage and one AC Current input with a user programmable sample rate from 1 second to 24 hours. LCD displays time/date, current reading, and min/max. Readings can be downloaded to your PC via the USB interface. Featuring Normal, Peak, and Capture (user specified trigger level) recording modes. Complete with 2 current clamps, two sets of test leads, 2 sets of alligator clips, software, USB cable, Universal AC Adapter, and 4 x AAA and 2 x CR2032 Batteries.
-
Xeltek
Features:Until now,Support IC manufacturer, pcs devices and keeps growing.1)High speed thanks to the flexible hardware engine. Programming speed adjustable for complicated application environments brought by user target board, length of ISP cable etc.2)Stand-alone and PC-Hosted (USB2.0 High Speed) dual mode;3)Supports ISP programming of devices with I2C, SPI, UART, BDM, MON, MW, JTAG, CAN, ICC, RS232 and any other serial port.4)ATE interface;5)Over-current and ESD protection to protect your equipment;6)DLL and API for easy integration into customers’ system.Hardware Specifications:1) ISP cable integrates I2C, SPI, UART, BDM, MON, MW, JTAG, CAN, ICC, RS232 interfaces。2) VDD (0-5.5V /0.5A) and Vpp (0-15V / 0.2A) lines provided to power the target board and the target devices.3) Cable driver circuit supports target devices of voltage level 1.5-5V and is ESD protected.4) USB 2.0 (high speed) interface for PC hosted mode and management of project files on SD card.5) A 20 Characters x 4 lines LCD and a 6-key keypad are built with it for stand-alone operation. In stand-alone mode project files are stored on the SD card (up to 16GB). The number of the project files is limited only by the capacity of the SD card.6) ATE interface is built for easy external hardware control. 6 lines SEL0-SEL5 are for project selection (maximum 64 files); 2 command lines START and STOP; 3 STATUS lines PASS, FAIL and BUSY. All signals are optical-isolated.7) A universal AC adaptor of DC12V/2A is included for power supply.8)WINDOWS XP/Vista/Win7/Win8/Win10 32/64bit compatibility.Software Specifications:1) Supports almost all devices with ISP interface.2) Supports Jam and Staple files from ACTEL and ALTERA; Direct C files from ACTEL.3) Programming speed selectable (High, Normal and Low) for complicated applications such as different cable lengths, different target load characters.4) Dynamic buffer function. Application examples include device S/N, MAC address, frequency or transducer calibration etc.5) File format on SD: FAT16, FAT32.6) Functions for IP protection: Project security, SD security, batch control, administration management etc. 7) API and DLL provided for easy integration into customers’ system like ICT and ATE.8) Software provides the features for multiple units to work concurrently controlled by USB HUB.Applications:1)R&D application like in-circuit test and debug.2)Volume production. Devices may be programmed after the board is fully assembled. One example is the serial number writing to an on-board serial device.3)Field application. Comes with portability, stand-alone mode and mobile data storage media (SD card), it is suitable for field test, debug and data acquisition.4)Third application modules. Friend s/w interface (DLL and Virtual Com communication command set) and h/w interface ( ATE and USB) are provided and make it very easy for customers to integrate ISP01 as a functional module into their systems. One example is the ICT equipment. With this integration user can finish in-circuit test and in-circuit programming in one step.
-
ICT IDE and Sequencer -
Konrad Technologies GmbH
The ICT software consists of two parts, the interactive development environment ICT IDE and the ICT sequencer. The IDE provides a graphical user interface for convenient creation and testing of these test sequences and allows:- Convenient management of hardware resources via topology editor- Support of several independent embedded testers for parallel test execution- Editing sequences in a text or table editor- Error highlighting during sequencing- Sequence execution (also single step) directly on a selected DUT- Debugging (single step)- Loop execution via sequences, or single steps- Optimization function with regard to waiting time and integration with Shmoo plot- detailed results output within tables as well as various results diagrams- Pin-Finder function to support adapter wiring- Automatic test program generation is available via Aster Testway
-
JT 2127/Flex Socket Test Module -
JTAG Technologies Inc.
The JT 2127/Flex STM memory socket tester is a family of hardware adapters specifically designed for the testing of of PCB-mounted DIMM & SODIMM sockets using a JTAG/boundary-scan controller and supporting software. The testing of memory sockets has always been troublesome for test and production engineers using JTAG/boundary-scan systems. Even when it is possible to create memory writes/reads from a boundary-scan compliant access device on the UUT (Unit Under Test), the initialization process may fail leaving you with little diagnostics information. What’s more it can still be uncertain whether fault lays with the DIMM module itself or the socket. Using the new JT 2127-Flex system from JTAG Technologies you get pin-point diagnostics from a known-good test interface so you can be certain that your socket is soldered correctly.
-
Extech PQ3350 -
Extech Instruments Corporation
Power measurements and analysis + datalogging of single and 3-phase/3-wire or 3-phase/4-wire systems (up to 52,428 single phase readings or 17,476 3-phase readings). Large backlighting LCD displays up to 35 parameters in one screen. Clamp-on True RMS power measurements with on-screen Harmonics display. Simultaneous display of Harmonics and Waveform. Display of Waveform with Peak Values (1024 samples/period). Analysis of Total Harmonic Distortion (THD-F). Maximum Demand (MDkW, MW, kVA, MVA) with programmable period. Adjustable CT ratio (1 to 600) and VT ratio (1 to 3000). Graphic Phase diagram with 3-Phase system parameters. 3-phase Voltage or Current Unbalanced Ratio (VUR, VIR) and Unbalanced Factor (d0%, d2%). Calculated Unbalanced Current through Neutral Line (In). Capture 28 Transient events (including Dip, Swell and Outage) with programmable threshold (%). Optically isolated USB interface with software to download Waveforms, Power Parameters and Harmonics. Includes 4 voltage leads with alligator clips and retractable plunger clips, 8 AA batteries, universal AC adaptor, software, USB interface cable, and case. Current Probes sold separately.
